RAVENOL DOT 5.1
- Specifications
- ISO 4925 Class 5-1
- FMVSS 116 DOT 5.1
- SAE J1704
- Categories
- Brake fluid
RAVENOL DOT 5.1 is a brake fluid for the use in all vehicles with optimum ABS characteristics. There is a chemical stability and it is provided with additives which save the best lubrication efficiency.
Because of the special formulation of RAVENOL DOT 5.1 the international specifications SAE J1704, ISO 4925 and the safety regulations FMVSS 116 DOT 5.1 from the United States of America are exceeded.
Application Notes
RAVENOL DOT 5.1 can be used in all vehicles for which the DOT 5.1 specification for brake fluids is required. It is suitable for all hydraulic brake systems with synthetic fluids.
RAVENOL DOT 5.1 is miscible with all known brake fluids of the same specification.
Characteristics
RAVENOL DOT 5.1 offers:
- optimum ABS characteristics
- chemical stability
- best lubrication efficiency
- neutral behaviour against brake parts
- low viscosity at low temperatures
- miscible with all brake fluids of the same specification
Property | Unit | Data | Audit |
---|---|---|---|
Colour | hellgelb | visual | |
Density at 20°C | kg/m³ | 1069 | EN ISO 12185 |
Boiling point | °C | 269 | SAE J1704 |
wet boiling point | °C | 187 | SAE J1704 |
Viscosity at -40°C | mPa*s | 810 | SAE J1704 |
kinematic viscosity at 100°C | mm²/s | 2,16 | ASTM D445 |
pH-Wert | 7,49 | FMVSS 116 | |
High Temperature Stability | °C | 0 | FMVSS 116 |
Chemical Stability | °C | 1,5 | FMVSS 116 |
Evaporation loss | Gew% | 68 | FMVSS 116 |
Fluidity & Appearance at -40°C | i.O., 2s | FMVSS 116 | |
Fluidity & Appearance at -50°C | i.O., 4s | FMVSS 116 | |
Water Tolerance at -40°C | klar, 2s | FMVSS 116 | |
Water Tolerance at +60°C | klar, keine Ablagerungen | FMVSS 116 | |
Compatibility at -40°C | klar, keine Phasentrennung | FMVSS 116 | |
Compatibility at +60°C | klar, keine Ablagerungen | FMVSS 116 | |
Water content | Gew.-% | 0,1 | Karl Fischer |
Corrosion Resistance | |||
Tinned Iron | Δ mg/cm² | -0,01 | FMVSS 116 |
_ | Aussehen | gut | |
Steel | Δ mg/cm² | -0,004 | FMVSS 116 |
_ | Aussehen | gut | |
Aluminium | Δ mg/cm² | -0,02 | FMVSS 116 |
_ | Aussehen | gut | |
Cast Iron | Δ mg/cm² | -0,01 | FMVSS 116 |
_ | Aussehen | gut | |
Brass | Δ mg/cm² | -0,05 | FMVSS 116 |
_ | Aussehen | gut | |
Copper | Δ mg/cm² | -0,03 | FMVSS 116 |
_ | Aussehen | gut | |
Zinc | Δ mg/cm² | 0,03 | FMVSS 116 |
_ | Aussehen | gut | |
Aussehen der Flüssigkeit | i.O. | FMVSS 116 | |
Ablagerungen | % | <0,05 | FMVSS 116 |
pH-Wert | 7,33 | FMVSS 116 | |
Veränderung des Durchmessers von Gummi | 0,03 | FMVSS 116 | |
Veränderung der Härte | IRHD | -6 | FMVSS 116 |
Erscheinungsbild | i.O. | FMVSS 116 | |
Tinned Iron | Δ mg/cm² | -0,01 | FMVSS 116 |
_ | Aussehen | gut | |
Aluminium | Δ mg/cm² | -0,01 | FMVSS 116 |
_ | Aussehen | gut | |
Beständigkeit gegen Gummi | |||
SBR bei 70°C | Ø Veränderung, mm | 0,44 | FMVSS 116 |
__ | Härte, IRHD | -6 | FMVSS 116 |
___ | Volumen, % | 4,31 | FMVSS 116 |
_ | Aussehen | gut | |
SBR bei 120°C | Ø Veränderung, mm | 0,72 | FMVSS 116 |
__ | Härte, IRHD | -11 | FMVSS 116 |
___ | Volumen, % | 8,47 | FMVSS 116 |
_ | Aussehen | gut | |
EPDM bei 70°C (Anforderung aus SAE J1703) | Härte, IRHD | -2 | FMVSS 116 |
___ | Volumen, % | 0,74 | FMVSS 116 |
_ | Aussehen | gut | |
EPDM bei 120°C | Härte, IRHD | -3 | FMVSS 116 |
___ | Volumen, % | 1,73 | FMVSS 116 |
_ | Aussehen | gut | |
Naturell bei 70°C (Anforderung aus ISO 4925) | Ø Veränderung, mm | 0,2 | FMVSS 116 |
__ | Härte, IRHD | -6 | FMVSS 116 |
___ | Volumen, % | 3,62 | FMVSS 116 |
_ | Aussehen | gut |